GMC C35
-
GMC C35 1992
VEHICLE DESCRIPTION: EXTENDED-CAB PICKUP TRUCKS EQUIPPED WITH HIGH-BACK BUCKET SEATS. THE SEAT RECLINER TO FRAME ATTACHING BOLTS CAN LOOSEN, FATIGUE, AND FRACTURE ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.
-
GMC C35 1994
VEHICLE DESCRIPTION: PICKUP TRUCKS, CREW CABS, UTILITY TRUCKS AND SPORT UTILITY VEHICLES. THESE VEHICLES WERE BUILT WITH THE POLARITY OF THE WIRING FOR THE ZERO ADJUST BRAKE SWITCH REVERSED FROM WHAT WAS SPECIFIED ON THE SWITCH DRAWING. WITH THE REVERSED POLARITY, THE CONTACTS IN THE BRAKE SWITCH CAN WEAR OUT PREMATURELY. THE BRAKE SWITCH WILL PERFORM NORMALLY UNTIL THE BRAKE SWITCH CONTACTS WEAR OUT, RESULTING IN LOSS OF THE BRAKE LAMPS WITHOUT ANY WARNING TO THE DRIVER.
-
GMC C35 1996
VEHICLE DESCRIPTION: EXTENDED CAB AND 2-DOOR UTILITY VEHICLES EQUIPPED WITH RECLINING SEATS AND THE EASY-ENTRY FEATURE. THESE VEHICLES EXHIBIT A CONDITION IN WHICH A PINCH POINT EXISTS IN THE RECLINER MECHANISM THAT CAN TRAP AND PINCH A PERSON'S HAND OR FINGER(S) WHEN THE EASY-ENTRY FEATURE IS ACTIVATED.
-
GMC C35 1995
VEHICLE DESCRIPTION: EXTENDED CAB AND 2-DOOR UTILITY VEHICLES EQUIPPED WITH RECLINING SEATS AND THE EASY-ENTRY FEATURE. THESE VEHICLES EXHIBIT A CONDITION IN WHICH A PINCH POINT EXISTS IN THE RECLINER MECHANISM THAT CAN TRAP AND PINCH A PERSON'S HAND OR FINGER(S) WHEN THE EASY-ENTRY FEATURE IS ACTIVATED.
-
GMC C35 1996
THESE TIRES HAVE BEAD DAMAGE WHICH OCCURED DURING TIRE MOUNTING.
-
GMC C35 1995
THESE TIRES HAVE BEAD DAMAGE WHICH OCCURED DURING TIRE MOUNTING.
-
GMC C35 1996
THE FOUR U-BOLTS NUTS ON EITHER SIDE OF THE REAR AXLE WERE UNDER-TORQUED.
-
GMC C35 1996
THESE VEHICLES WERE ASSEMBLED WITH THE THROTTLE CABLE CONTACTING THE DASH MAT WHICH COULD BIND THE THROTTLE. THIS DOES NOT MEET WITH THE MAXIMUM RETURN TIMES REQUIRED BY FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 124, ACCELERATOR CONTROL SYSTEMS.
-
GMC C35 1995
THESE VEHICLES WERE ASSEMBLED WITH THE THROTTLE CABLE CONTACTING THE DASH MAT WHICH COULD BIND THE THROTTLE. THIS DOES NOT MEET WITH THE MAXIMUM RETURN TIMES REQUIRED BY FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 124, ACCELERATOR CONTROL SYSTEMS.
-
GMC C35 1996
THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLES COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.
-
GMC C35 1995
THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLES COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.
-
GMC C35 1994
THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLES COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.
-
GMC C35 1995
THE STEERING COLUMN UPPER INTERMEDIATE-SHAFT NUT MAY NOT BE TORQUED TO PROPER SPECIFICATIONS. THE NUT COULD LOOSEN AND DETACH ALLOWING THE THROUGH-BOLT THAT SECURES THE UPPER INTERMEDIATE-SHAFT TO THE LOWER STEERING COLUMN SHAFT JOINT TO FALL OUT.
-
GMC C35 1996
CERTAIN TRUCKS HAVE FUEL RAIL ASSEMBLIES WITH AN IMPROPERLY CRIMPED END RETAINER CLIP THAT RESULTS IN A FUEL LEAK.
-
GMC C35 1994
THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLE COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.
-
GMC C35 1993
THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLE COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.
-
GMC C35 1995
IF BOTH THE LAP-BELT AND SHOULDER-BELT ENERGY MANAGEMENT LOOPS ON THE FRONT SEAT BELT ASSEMBLIES RELEASE AT OR NEAR THE SAME TIME, ACCELERATION FORCES CAN CAUSE THE BUCKLE RELEASE MECHANISM TO ACTIVATE AND ALLOW THE BUCKLE TO SEPARATE FROM THE LATCH.
-
GMC C35 1994
IF BOTH THE LAP-BELT AND SHOULDER-BELT ENERGY MANAGEMENT LOOPS ON THE FRONT SEAT BELT ASSEMBLIES RELEASE AT OR NEAR THE SAME TIME, ACCELERATION FORCES CAN CAUSE THE BUCKLE RELEASE MECHANISM TO ACTIVATE AND ALLOW THE BUCKLE TO SEPARATE FROM THE LATCH.
-
GMC C35 1995
THESE VEHICLES WERE BUILT WITH FRONT SEAT BELT SYSTEMS WITH NO ENERGY MANAGEMENT LOOPS AND MAY NOT MEET THE HEAD INJURY CRITERIA REQUIREMENTS OF FMVSS NO. 208, OCCUPANT CRASH PROTECTION.
-
GMC C35 1994
THESE VEHICLES WERE BUILT WITH FRONT SEAT BELT SYSTEMS WITH NO ENERGY MANAGEMENT LOOPS AND MAY NOT MEET THE HEAD INJURY CRITERIA REQUIREMENTS OF FMVSS NO. 208, OCCUPANT CRASH PROTECTION.
-
GMC C35 1995
DUE TO A THIN CASE CASTING, AN EXTERNAL TRANSMISSION LEAK CAN OCCUR.
-
GMC C35 1994
VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS, VANS AND MOTORHOMES EQUIPPED WITH ELECTRONICALLY FUEL INJECTED 6.5L DIESEL ENGINE. THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH FEDERAL REGULATION PART 573. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. THE CAMPAIGN WILL IMPROVE THE OVERALL DRIVEABILITY OF THESE VEHICLES.
-
GMC C35 1994
TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.
-
GMC C35 1994
THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, SEATING SYSTEMS.
-
GMC C35 1993
THE REAR BENCH SEAT DOES NOT MEET THE LOAD REQUIREMENTS OF FMVSS 207, SEATING SYSTEMS, BECAUSE THE MANUAL LATCH MECHANISM ON THE FOLDING FULL BENCH REAR SEAT WAS ATTACHED TO THE BACK FRAME LOWER CROSS TUBE WITH DOMED HEAD STEEL RIVETS INSTEAD OF THE BOLTS SPECIFIED.
-
GMC C35 1994
THE BRAKE PEDAL PUSH ROD RETAINER IS MISSING, MISPOSITIONED OR NOT PROPERLY SEATED.
-
GMC C35 1991
THERE MAY BE FATIGUE FRACTURES OF THE TIE ROD THROUGH THE DAMPER STUD MOUNTING HOLE.
-
GMC C35 1986
THE LEFT HAND LOWER CONTROL ARM CAN CRACK STARTING AT THE REAR FLANGE AND PROGRESSING TO THE BALL JOINT MOUNTING HOLE AND EVENTUALLY CAUSE THE LOWER BALL JOINT TO SEPARATE FROM THE CONTROL ARM.
-
GMC C35 1985
THE LEFT HAND LOWER CONTROL ARM CAN CRACK STARTING AT THE REAR FLANGE AND PROGRESSING TO THE BALL JOINT MOUNTING HOLE AND EVENTUALLY CAUSE THE LOWER BALL JOINT TO SEPARATE FROM THE CONTROL ARM.
-
GMC C35 1990
LOOSE PIVOT BOLT HOLDING THE BRAKE PEDAL TO ITS SUPPORT BRACKET COULD DISENGAGE FROM THE NUT.